Replacement Locks For Patio Doors at Lowe's
Replacing your patio door lock is an easy method to increase your home's security. However, it is essential to perform routine maintenance and install the lock correctly.
In order to successfully replace the patio door lock it is crucial to know what the type of your existing one is. The size of the screw hole and kind of faceplate at the end will assist you in identifying the kind of lock you are replacing.
Identifying Your Lock's Existing Lock
It is important to understand the distinctions between various types of locks prior to deciding to purchase a new lock. This will allow you to locate the ideal replacement, and ensure that your home is safe and secure.
The most well-known type of lock is the cylinder lock also known as pin and tumbler locks. This lock type makes use of a combination of top pins, bottom pins, and springs to keep the key hole and plug secured. Cylinder locks come in a variety of different sizes, and it is important to know the exact length and width of your current cylinder before buying an alternative.
To measure the width of your existing lock using a screwdriver, loosen the screws holding the cylinder and then carefully pull it out. Then, you can measure the distance in millimeters between the outer edge and the inner end of the cylinder. Compare this measurement with the measurements of the lock you are planning to purchase. This will help ensure that your new lock is of the right size and will fit in the hole of the door lock that is already in place.
upvc door locks replacement can be used to test the dimensions of a lock that is already in use. If the key can slide into the cylinder without difficulty and is in the correct size, it's the width of the rekeying kit that you need. If the key will not slide into the cylinder, your cylinder could have a different keyway and therefore, it is not rekeyable in a way that it will accept that brand of key.
It is best to always follow the instructions supplied by the manufacturer that come with a kit for rekeying. Each type of lock will have its own set of unique installation requirements. It is recommended to take the time to fully test the new lock after it has been installed to ensure it works properly and provides you with maximum security. It is also essential to pay attention to any additional features your new lock may have in order to determine the ease of operate.
Take a measurement of the Width
A broken patio door lock can cause serious security issues. It is crucial to examine your locks on a regular basis and replace them if needed. This will ensure that they're operating properly and are secure. It can also help prevent issues such as a damaged latch or keyway. If your current locks are damaged or worn out, damaged, you can get replacements at Lowe's that will give you the security you need for your home.
Before you purchase a new patio door lock, you need to determine the dimensions of your existing one. This will help you determine the size of lock you should purchase and avoid the possibility of purchasing a lock that does not fit. You'll need two measurements in order to do this which are the backset and case depth. The first is a distance between the edge of a lock's face and that of the middle of the hole through which the handle spindle goes through. The second refers to observing the depth of a lock from the outside.
When deciding on the type of lock you want to use it is essential to think about how you will be using your doors. If your sliding doors open horizontally, you'll need top-and-bottom tab lock that is able to engage with the strikeplate, preventing it from being lifted or opened. If your patio doors open vertically, you will have to select mortise latches that have an attached hook latch that is spring loaded for extra security.
It's important to note the location of the screw holes when determining the size of your lock. Some mortise locks have round screws and others have square ones. You'll also have to know the location of the keyway. Some locks have a vertical keyway, while others are 45-degree angled. It is a good idea to capture a picture of the lock that is in use with your digital camera before you take it off to ensure that you get the correct replacement.
After you've gotten your measurements and have a plan for your home, it's time to search for a new patio door lock. On the internet, you can find a wide range of top-quality locks. A lot of the top brands offer advanced security features to safeguard your home. Selecting the right lock is an investment in your home's safety, so it's important to research and read reviews prior to making a purchase. Also, make sure to regularly clean your locks to keep dirt and dust from affecting the functionality of your doors.
Make sure you check the screw holes
Patio doors play an important role in securing your home and should be inspected for signs of wear and tear to make sure they're operating correctly. As time passes, your locks and spindle that connects the handles on the exterior and interior will require replacement. A sturdy lock will not only help stop unwanted entry but will also improve security, efficiency and safety.
There are a variety of ways to narrow your search for a new lock if you don't have the specific type. First, you must determine the type of keyway that is used. Aluminum patio doors are typically fitted with rectangular cutout mortise lock, while E2126 or E2079 locks are set in a recess on the frame. Uploading a picture of the lock using your digital camera can help you identify the type of lock it is.
Another method to determine the type of lock you have is by observing the screw holes. Most sliding patio door locks have screw holes that are aligned with the latch keeper that is mounted on the side jamb, but they are not always identical. Some screws may be longer than others or have a different threaded finish. Some screws also have washers or a hex nut attached to them, which can affect the way they fit into the lock hasp.
Once you know what type of lock your home is secured with, you can begin preparing to replace it. You'll need to clean the lock first with a damp brush or cloth to remove any debris that could hinder its operation. After the lock has been cleaned then you can apply a silicone-based grease to keep it clean and quiet.
It's a great idea replace your old screws with more long screws. This will allow you to get an improved grip, and install the lock with less effort. After you've completed that, it's a good idea test the handle and observe how the latch hasp is engaged inside the lock.
If it's not able to engage quickly it could be necessary to install a washer or hex nut behind the hasp to allow it to hold more of the door's lip. You can add an shim on the sides of the lockkeeper's jamb and see if that helps.
Check the Lock Snib
The snib acts as the lock mechanism located inside the door handle. The snib is able to be disengaged and engaged to open or close your patio doors and is the first thing you need to look at if your locks aren't functioning correctly. You can also check the keepers located at the top and bottom of your door frames to see if there is any misalignment or looseness which could cause them to break. Check that your snib lock is seated properly, and that the lock isn't jammed or otherwise blocked in any way.
The most commonly used patio door locks are made of steel mortise latches that hold your sliding glass doors in place. They are inserted into the door frame and are available in a variety of styles, making them an effective security measure. Some are designed to hold keys while others have an oval cutout that makes it easy to lock and unlock.
Another option that is popular is a step-on lock that has a thumb-screw design that will securely hold your sliding doors in place without having you to turn the knob or use the key. These locks are typically used on older patio doors, but they can be a great choice to secure wood or vinyl-framed sliding doors as well.
When you inspect your existing patio lock, take note of the type and size screw holes used to mount the escutcheon and the lock body. This will allow you to pick a lock that has the proper screw holes. It's a good idea to examine your strike plate to ensure it's securely secured.
If you have Jason Windows boltlock slider doors between 2000 and 2009, ensure that the screws that hold the door in place and aren't missing or loose. These screws hold the snib in a partially open "vent" mode, allowing airflow while promoting security. They are also important to avoid your lock being smashed. It is recommended for all locks to be inspected regularly and cleaned regularly to avoid debris, dirt or corrosion from obstructing the operation the lock.
If your snib is damaged you might be able to replace the entire strikeplate and the snib. If, however, your snib is just wrongly aligned, you can correct it yourself by taking the strike plate off with a putty knife, and then backing out the adjustment screw (located above and below the screw) to shift the strike plate upwards or down until its engagement tongue is aligned with the Milgard logo on the snib.